Programming Opener Remotes Programming Instructions for Genie remotes: Programming Genie Intellicode Remote Transmitters • Gently press and release the Receiver Learn Code button on the power head receiver of your door operator. This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. ** • After pressing the Learn Code Button once, press your transmitter button three times for your system to grab the frequency and code it in. (Keep the transmitter you want tuned at least 2 feet away from the power head while tuning.) • Press the transmitter button once more to test the system and start your door moving. **To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 1.

To erase all codes, press and hold the Learn button until the Learn LED light goes out, which should take about 6 seconds. You should then be able program your remotes for that garage door opener. Programming Troubleshooting. If you're still having trouble, weak batteries could be preventing you from programming your remotes. My sears craftsman garage door opener model# 139.53615SR opens when my neighbor opens his garage. I tried to reset the codes by holding the learn key momentarily, for. Now we’ll show you how to program a single universal remote to operate multiple garage door openers. You can program each of the universal remote’s three buttons to open a different garage door. To program a universal remote to open two garage doors, start by using the remote’s visor clip to press and release the recessed button. Press and release the Learn button on your first garage door opener motor unit.

For Genie IntelliG, TriloG, SilentMax, PowerMax, GPower, and PowerLift Series Openers ( Intellicode II ) These include models 4024, 3024, 4042, 3042, 4022, 3022, and 4064, 3064, 4062, 3062, 2564, 2562. Looking up in your garage at the bottom of your Genie motor cover is a set of black buttons, depicted in the drawing below, along with two LED lights shown here in grey. • Press and hold down the square button on the motor head until the round blue LED light come on, then release the square button. • The long purple LED button will start to blink. ( Note: if the blue light stays on, go to instructions for Intellicode III, below ) • While the long LED is blinking, hold the remote 4 or 5 feet away and press 3, 4 or 5 times, until the door activates. Your remote is now programmed.

To clear all remotes and keypad from the system, follow Steps 1 and 2. After Step 2, while the purple LED is blinking, press and hold both triangular button until the purple LED goes out. This clears the radio receiver’s memory.

For Genie IntelliG, TriloG Series built from 2009 until July 8, 2011 ( Intellicode III ) (see serial # on front: first 2 digits = year, next 3 digits = day of the year) • Press and hold down the square button on the motor head until the round blue LED comes on, then release the button. Press the square button once more until the long purple LED comes on and release. The purple LED should be blinking. • To unlock the programming feature use a remote that already operates the unit and press it once. Purple light goes solid.

• Hold the new remote 4 or 5 feet away and press 3, 4 or 5 times until the door activates. The remote is then programmed Clearing Memory for Remotes and Keypad (if present) • Follow steps 1 and 2 above or step 1 if between 2009 and July 8, 2011. Graphicriver - Lines Photoshop Action 11498611 - Download Free Apps. • While the long purple LED is blinking hold down on the UP and DOWN triangle buttons at the same time until both LEDs flash blue and go off. This clears the receiver memory. All previously programmed remotes will no longer work with your door. • To re-program each remote follow steps 1 through 3 of the programing instructions relative to your opener above. Programming Digital Remote Transmitters with Internal Set Switches These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling.

The receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work. Genie has been making the 390 MHz frequency exclusively for the last 15 years.